JUNSI/ICHARGER 4512DUO

SKU: iCharger 4512DUO

HAN: #802.

Category: JUNSI

Low stock level
Delivery time: 1 - 3 Workdays (DE - int. shipments may differ)

487,90 €

incl. 19% VAT ,

Manufacturers recommended retail price: 489,90 €

(Save 0.41%, i.e. 2,00 €)

iCharger 4512DUO – the redesigned successor to the 4010DUO: 2800W, 1–12S LiXx, up to 45A per output and 80A in synchronous mode, Digital Power up to 50V.

pcs

description
Reviews

Junsi iCharger 4512DUO – 2800W for 12S

With the iCharger 4512DUO, Junsi has completely re-engineered the well-known 4010DUO: significantly more power and new features. Both charge outputs are fitted with high-current XT90 connectors.

2800W charging power (from 40V), 1–12S LiXx batteries and up to 45A charge current are enough even for large high-capacity batteries. Of course you can also charge LiHV, Li-Ion, NiZn, Pb, NiCd and NiMH.

The discharge power is 200W in total and can be increased to up to 2800W with an external load. Regenerative discharging into the supply battery is also possible.

Highlights

USB-C PD port for charging smartphones (5V/3A, 9V/2A, 12V/1.5A) and for software updates
Micro SD slot for data logging and updates
Digital Power: one output becomes a regulated power supply with 2–50V and 1–45A (provided a suitable supply is used)
Integrated servo tester (external power supply required)

Specifications

Outputs	2 × XT90
Battery types	1–12S LiPo and LiHV, 1–32 NiCd/NiMH cells, lead-acid batteries up to 40V
Charge current	0.05–45A per output, 0.05–80A in synchronous mode
Charging power	2800W (from 40V), 2000W on one output
Discharge power	200W total without external load, 120W per output
External discharge	up to 2800W
Regenerative discharge	up to 45A
Balance current	2A per output, 4A in synchronous mode
Input voltage	11–53V DC
Input current	max. 80A
Connectors	Input EC8, charge output XT90
Built-in power supply	no
Display	2.8" IPS
Dimensions	210 × 140 × 80mm (identical to the 4010DUO)

Charging 12S with two balance connectors (2 × 6S)

For 12S, your battery needs a 13-pin XH balance connector. To charge 2 × 6S as 12S, you also need the CB12-XH balance adapter board with the BW-13-13 cable (not included). For 10S as 2 × 5S, you can use the CB-1010 with the 11-11 cable.

First connect the charger to the power supply or supply battery. If you use a power supply, switch it on beforehand.
Plug the first balance connector (cells 1–6, negative side of the battery, black wire) into the matching 6S slot on the board – starting from the negative side.
Then plug the second balance connector (cells 6–12, positive side of the battery, red wire) into the second 6S slot – starting from the positive side.
Only connect the board to the charger once both batteries are correctly plugged into the board.
Finally, connect the thick red main charge lead (+) and then the thick black main charge lead (–) to the charger.

Avoid short circuits, otherwise there is a risk of injury. This sequence also applies when you charge several batteries in series. You are responsible for any damage caused by not following these instructions.

Good to know

Important: Make sure you set the correct power source in the charger, otherwise defects may occur that are not covered by the warranty. Example: your power supply delivers 600W at 24V – then you set 24V and max. 25A (600W / 24V = 25A).
All Junsi chargers in the X and DUO series are designed and approved for use in RC modelling. Industrial use is not intended and not permitted.
Only operate the charger with power supplies designed for RC modelling. AGM batteries must not be charged using the Pb programme.
The menu navigation is almost identical to the well-known iCharger models 3XXDUO, 45XDUO and 4010DUO.
The manual is supplied in English; a German version is available to download from our shop.

Scope of delivery

iCharger 4512DUO
2 × XT90 female
EC8 cable for custom assembly (counterpart to the charger connector)

Product safety

Warning and safety notice: CAUTION: Not suitable for children under 14 years of age. Use only under the direct supervision of adults.

Manufacturer: Shenzhen New Junsi Electronic Co.,Ltd (JUNSI), Room 208, Huaxuan Building Haibin Plaza, Ji, 518033 Futian, Shenzhen, China (CN), e-mail: szjunsi@163.com

Responsible person (EU): SieBra GmbH & Co. KG, Christian-Liebrecht-Straße 6, 58739 Wickede, Germany (DE), phone: +49 2307 146280, web: www.rc-dome.de, e-mail: info@rc-dome.de

There are no reviews yet.

Manufacturer according to GPSR
RC-Dome, Christian-Liebrecht-Straße 6 6, 58739 Wickede, https://www.rc-dome.de/

Sale 5%